752ELECTRONIC GUIDANCE SYSTEMS

Location, depth, roll angle, pitch, beacon temperature, battery status—the Ditch Witch Electronics 752 Tracker and 752 Display see all and tell all. The lightweight, exceptionally durable 752 system works with Ditch Witch directional drilling beacons to provide the vital information you need for a successful HDD system installation.

KEY FEATURES

DETAILS

LITERATURE

MANUAL

OFFERS

SPECS

SAFETY

JOB RELATED

Untitled Document

752 Tracker Electronic Guidance Systems 1

1 2 3

KEY FEATURES,

752

The 752 Tracker provides comprehensive guidance data for shallow bores, deep bores, or a combination of the two, using walkover beacon tracking, remote guidance and line locating capabilities.
The 752 Display can receive data up to 2000 feet (610 m), store up to ten jobs of 254 pipes each, and provide downloads to the TMS Plus system.

DETAILS,

752

REQUEST MORE INFO

The 752 Tracker tracks bore depths of 9" to 70 feet
(229 mm to 21 m).
The water- and shock-resistant 752 Tracker is made with high-impact Xenoy^® plastic.
The 752 Display provides left/right arrow indicators as well as a distance estimate from the tracker to the beacon to make tracking easier.
752 Display shows beacon temperature in degrees and alerts the operator to prevent overheating.

Downloaded jobs can be merged with bore plans for comparison.
The 752 remote display provides an accurate report of the status of the beacon.
The 752 Tracker's 12-segment clock face indicates the roll angle of the tool face; pitch angle is displayed using both up/down arrows and numerical percentages.

LITERATURE,

752

Select your language to view PDF

English

MANUAL,

752

MANUAL

TRACKER MANUAL

SPECIFICATIONS,

752

752 TRACKER	U.S.	METRIC

TRACKER DIMENSIONS	U.S.	METRIC
Depth	12.8 in	325 mm
Height	31.5 in	800 mm
Width	6 in	150 mm
Operating weight	5.5 lb	2.5 kg
Operating temperature range	-4° F to 122° F	-20° C to 50° C
Antenna configuration: Peak
Operating modes: 29 K beacon, 60 Hz power, 50 Hz power, 8 kHz line
MAXIMUM LOCATING RANGE*	U.S.	METRIC
Beacon	9.6 in-100 ft	20 mm-30 m
Line	0 ft - 10 ft	0 m - 3 m
BEACON DEPTH ESTIMATE TOLERANCES*	U.S.	METRIC
± 4 in/10 cm @	10 ft	3 m
± 5% @	10 ft - 20 ft	3 m - 6.1 m
± 10%	Beyond 20 ft	Beyond 6.1 m
LINE LOCATION DEPTH ESTIMATE TOLERANCES*	U.S.	METRIC
Active mode
± 3% @	10 ft	3 m
Passive mode
± 5% @	6 ft	1.8 m
± 10% @	10 ft	3 m
BATTERY
Number/type: 6 C-cell alkaline
Battery life**: Approximately 20 hours
Battery saver: Unit shuts off after 5 minutes if no key is pressed
RADIO
Type: 9-channel, dual-conversion, narrow-band FM
Frequency range: 420 mHz - 470 mHz
Sensitivity: 110 dBm for 12 dB sinad (typical)
752 DISPLAY	U.S.	METRIC

DISPLAY DIMENSIONS	U.S.	METRIC
Module only
Operating weight	2.5 lb	1.1 kg
Power input: 6.5V DC - 16V DC at approximately 150 mA
Interface connectors: DB-15P (D-series subminiature male)
Module with case
Operating weight	6.5 lb	3 kg
Battery	6 C-cell alkaline
Interface	MS5015 (7 pin)
Antenna	TNC female

Specifications are general and subject to change without notice. If exact measurements are required, equipment should be weighed and measured. Due to selected options, delivered equipment may not necessarily match that shown. Units are calibrated to these tolerances under test field conditions. Actual field conditions may cause signal distortions or may contain noise sources which result in depth estimates that vary from these figures. *Continuous use at 70° F (21° C).

ATTACHMENTS,

752

TRAILERS,

752

JOB RELATED, 752

Meet Selge Construction
In the 47 years the company has been in business, Selge Construction, Niles, Michigan, has built a reputation as one of the most respected utility contractors in the Southwest Michigan-South Bend, Indiana, area.